background image

Tour of the Machine

KVAL Operation/Service Manual

2-12 

About the Front Section

As the door is processed the 

Front Section

 performs Jamb and Hinge machining. Simultaneously, 

the 

Back Section 

performs lock and faceplate machining. The 

Front Section 

performs the follow-

ing:

• Jamb is placed into Jamb Holder and clamped into place
• Carriage Heads rout hinge pockets on jamb and door edge
• Carriage Heads pre-drill pilot holes for Hinge application
• Hoppers deliver screws to Six Shooters by way of a air tube
• Six Shooters drop down and drill hinge into place on jamb and the door edge.

FIGURE 2-4.

Front Section

Carriage 
Head #1

Carriage 
Head #2

Carriage 
Head #3

Screws Transported

Six 

Shooter 

#1

Carriage 
Head #4 

Six 

Shooter 

#2

Six 

Shooter 

#3

Six 

Shooter 

#4

When processing 

8’-0”

 doors 

all Carriage 

Heads and Six Shooters

 are used to pro-

cess a door.

When Processing a 

6’-8” and a 7’-0”

 Door, 

Six 

Shooter #1

 and 

Carriage Head #1 

are put in the 

parked position and not used. 

Six Shooters

 and 

Carriage Heads #2 - #4

 are used to process the 

door.

Hopper 

#1

Hopper 

#2

Hopper 

#4

Hopper 

#3

Summary of Contents for 990FX













































































































































































Reviews: