Kubota WSM L3540-II Workshop Manual Download Page 361

Page: 361 / 672

TRANSMISSION

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

3-S115

Thickness of Seal Ring

1. Measure the thickness of seal rings (1) with an outside

micrometer.

2. If the measurement is less than the allowable limit, replace it.

9Y1211167TRS0155US0

(4) Differential Gears

Spiral Bevel Gear Turning Torque

NOTE

• It is necessary to adjust the spiral bevel gear turning

torque, when replacing the differential gears, transmission
case or other relative parts.

1. Assemble the differential gears to transmission case. At this

time, install the some shims (3) to the spiral bevel gear side.

2. Check the turning torque by using turning torque tool (1).

Turning Torque Tool:
Weld socket on the brake shaft
(Brake shaft Part No. TA040-26710)

3. Add or reduce the thickness of shims (3) to make the specified

turning torque.

4. After getting the specified turning torque, divide the thickness of

shims to left and right side.

5. Assemble the transmission case and adjust the backlash and

tooth contact with spiral bevel pinion.

9Y1211167TRS0156US0

Thickness of seal ring

Factory specification

2.45 to 2.50 mm
0.0965 to 0.0984 in.

Allowable limit

2.0 mm
0.079 in.

(1) Seal Ring

Turning torque of 37T
spiral bevel gear

Factory specification

4.0 to 6.3 N·m
0.40 to 0.65 kgf·m
2.9 to 4.7 lbf·ft

(1) Turning Torque Tool
(2) 37T Spiral Bevel Gear

(3) Adjusting Shim
(4) Differential Support

KiSC issued 02, 2015 A

Summary of Contents for WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for WSM L3540-II

Reviews:

Related manuals for WSM L3540-II

Brands by name

Popular brands

Kubota WSM L3540-II, Workshop Manual

Search results

Summary of Contents for WSM L3540-II

Reviews:

Related manuals for WSM L3540-II

Brands by name

Popular brands