manualshive.com logo in svg

Kubota WSM L3540-II, Workshop Manual, Page: 310 / 672

Share
Download
Kubota WSM L3540-II Workshop Manual Download Page 310

TRANSMISSION

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

3-S64

Disassembling Shaft Assemblies

1. Disassembling the each shaft referring to the figure.

9Y1211167TRS0068US0

Differential Lock Shift Fork

1. Tap out the left side spring pin (4).
2. Remove the cotter pin and remove the clevis pin (3).
3. Draw out the differential lock fork shaft (1) and remove the

differential lock shift fork (2).

(When reassembling)

• Apply grease to the left and right oil seals on the transmission

case.

• Insert the clevis pin (3) from the top and install the washer and

cotter pin.

• Tap in the spring pin (4) so that its split portion 

"a"

 may face

outward as shown in the figure.

9Y1211167TRS0069US0

(1) 20T-49T Gear
(2) Range Gear Shaft
(3) 17T Gear
(4) Needle Bearing
(5) 34T Gear (L3240, L4240) 

35T Gear (L3940)

(6) 18T Gear (L3240)

19T Gear (L3940)
16T Gear (L4240)

(7) Spiral Bevel Pinion Shaft
(8) 29T Gear (L3240, L3940)

31T Gear (L4240)

(9) PTO Drive Shaft
(10) 27T Gear (L3240, L3940)
(11) Front Wheel Drive Shaft
(12) 24T Shifter Gear 

(L3240 (4WD Only), L3940)
22T Shifter Gear (L4240)

(13) 26T-60T Gear (L3240, L3940)

[A] L3240, L3940
[B] L4240

(1) Differential Lock Fork Shaft
(2) DIfferential Lock Shift Fork
(3) Clevis Pin
(4) Spring Pin

a:

Split Portion

KiSC issued 02, 2015 A 

Summary of Contents for WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments