manualshive.com logo in svg

Kubota WSM L3540-II, Workshop Manual, Page: 319 / 672

Share
Download
Kubota WSM L3540-II Workshop Manual Download Page 319

TRANSMISSION

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

3-S73

Shaft Assemblies

1. Remove the external snap ring (1) and thrust collar (2).
2. Draw out the shaft assemblies (4), (5), (6), (7), (9) and shift forks

(10) and rods.

3. Pull out the front axle drive shaft (8) to the rear side.

(When reassembling)

• Install the front axle drive shaft (8) from front side after

assembling the clutch housing and mid case. Then install the
bearing (13), sleeve (14), collar (15), oil seal (12), internal snap
ring (11), O-ring (16) and spacer (17) in order.

9Y1211167TRS0083US0

(1) External Snap Ring
(2) Collar
(3) Shuttle Shift Arm
(4) 18T Gear Shaft Assembly
(5) Idle Shaft Assembly
(6) PTO Counter Shaft Assembly
(7) Main Gear Shaft Assembly
(8) Front Axle Drive Shaft
(9) Counter Shaft Assembly
(10) Shift Fork

(11) Internal Snap Ring
(12) Oil Seal
(13) Bearing
(14) Sleeve
(15) Collar
(16) O-ring
(17) Spacer

F:

Front Side

KiSC issued 02, 2015 A 

Summary of Contents for WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments