manualshive.com logo in svg

Kubota WSM L3540-II, Workshop Manual

The Kubota WSM L3540-II Workshop Manual is a comprehensive guide for maintaining and repairing your Kubota tractor. This manual includes detailed instructions and diagrams to help you troubleshoot and fix any issues with your equipment. Download it for free from manualshive.com today.

Share
Download
background image

CONTENTS

1. TROUBLESHOOTING.................................................................................................................1-S1
2. SERVICING SPECIFICATIONS ..................................................................................................1-S4
3. TIGHTENING TORQUES..........................................................................................................1-S10

[1] CABIN MODEL....................................................................................................................1-S10
[2] ENGINE...............................................................................................................................1-S11

4. CHECKING AND ADJUSTING..................................................................................................1-S12

[1] ENGINE BODY....................................................................................................................1-S12
[2] LUBRICATING SYSTEM.....................................................................................................1-S14
[3] COOLING SYSTEM ............................................................................................................1-S14
[4] FUEL SYSTEM....................................................................................................................1-S17
[5] TURBOCHARGER (IF EQUIPPED) ....................................................................................1-S21

5. PREPARATION .........................................................................................................................1-S22

[1] SEPARATING ENGINE FROM TRACTOR.........................................................................1-S22

6. DISASSEMBLING AND ASSEMBLING ....................................................................................1-S36

[1] OUTER PARTS ...................................................................................................................1-S36
[2] EGR VALVE AND EGR COOLER (IF EQUIPPED) ............................................................1-S37
[3] CYLINDER HEAD AND VALVES........................................................................................1-S38
[4] TIMING GEARS, CAMSHAFT AND FUEL CAMSHAFT .....................................................1-S43
[5] PISTON AND CONNECTING ROD ....................................................................................1-S49
[6] CRANKSHAFT ....................................................................................................................1-S52

7. SERVICING ...............................................................................................................................1-S55

[1] CYLINDER HEAD AND VALVES........................................................................................1-S55
[2] TIMING GEARS, CAMSHAFT AND FUEL CAMSHAFT .....................................................1-S61
[3] PISTON AND CONNECTING ROD ....................................................................................1-S65
[4] CRANKSHAFT ....................................................................................................................1-S67
[5] CYLINDER ..........................................................................................................................1-S71
[6] OIL PUMP ...........................................................................................................................1-S72

SERVICING

KiSC issued 02, 2015 A 

Summary of Contents for WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for WSM L3540-II

Rankin JLF-2242 Operator'S / Parts Book preview
JLF-2242
Brand: Rankin Pages: 30
Tiger BENGAL JD6 E T4F Series Mounting And Operating Instructions preview
BENGAL JD6 E T4F Series
Brand: Tiger Pages: 244
Tar River CSP Installation Instructions Manual preview
CSP
Brand: Tar River Pages: 9
DongFeng DFH4180 Series User Manual preview
DFH4180 Series
Brand: DongFeng Pages: 251
DRESSTA 32501 Operator'S Manual preview
32501
Brand: DRESSTA Pages: 177
Cub Cadet 3184 Operator'S Manual preview
3184
Brand: Cub Cadet Pages: 56
Valtra T2 Versu Series Operator'S Manual preview
T2 Versu Series
Brand: Valtra Pages: 36
GE UCG1680 Owner'S Manual preview
UCG1680
Brand: GE Pages: 24
Cadet 1212 Operator'S Manual preview
1212
Brand: Cadet Pages: 40
Whirlpool Compactor Use And Care Manual preview
Compactor
Brand: Whirlpool Pages: 16
Yanmar YM276 Service Manual preview
YM276
Brand: Yanmar Pages: 662
Centro 85-1066-6 (A01001 Safe Use, Care And Assembly Manual preview
85-1066-6 (A01001
Brand: Centro Pages: 8
Summit S-V2 Maintenance Manual preview
S-V2
Brand: Summit Pages: 35
New Holland T4030V Specifications preview
T4030V
Brand: New Holland Pages: 2
New Holland MY16 Repair Manual preview
MY16
Brand: New Holland Pages: 4
New Holland T6.110 Service Manual preview
T6.110
Brand: New Holland Pages: 51
New Holland T3010 Service Manual preview
T3010
Brand: New Holland Pages: 9
New Holland EXITUS T175E (Portuguese) Brochure & Specs preview
EXITUS T175E
Brand: New Holland Pages: 6

Brands by name

Popular brands

Load more brands