KSB Magnochem-Bloc Installation & Operating Manual Download Page 22

Page: 22 / 96

5 Installation at Site

22 of 96

Magnochem-Bloc

CAUTION

Neither mounting plate nor foundation rails must be set in concrete.

5.3.1 Installation without foundation

Fig. 6:

Adjusting the levelling elements

1, 3

Locknut

Adjusting nut

Machine mount

The installation surface has the required strength and characteristics.

1. Position the pump set on the machine mounts (4) and align it with the help of a

spirit level (on the shaft/discharge nozzle).

2. To adjust any differences in height, loosen the locknuts (1, 3) of the machine

mounts (4).

3. Turn the adjusting nut (2) until any differences in height have been

compensated.

4. Re-tighten the locknuts (1, 3) at the machine mounts (4).

Summary of Contents for Magnochem-Bloc

































































































Search results

Summary of Contents for Magnochem-Bloc

Reviews:

Related manuals for Magnochem-Bloc

Brands by name

Popular brands

KSB Magnochem-Bloc, Installation & Operating Manual

Search results

Summary of Contents for Magnochem-Bloc

Reviews:

Related manuals for Magnochem-Bloc

Brands by name

Popular brands