KSB Magnochem-Bloc Installation & Operating Manual Download Page 59 | Manualshive

Page: 59 / 96

background image

7 Servicing/Maintenance

59 of 96

Magnochem-Bloc

7.5 Reassembling the pump set

7.5.1 General information/Safety regulations

DANGER

Strong magnetic field in the area of the magnetic coupling or the individual
magnets

Danger of death for persons with pacemaker!

Interference with magnetic data carriers, electronic devices, components and
instruments!

Uncontrolled magnetic attraction forces between magnet-equipped components,
tools or similar!

▷

Keep a safety distance of at least 0.3 m.

▷

Also observe the additional instructions. (

Section 2.10, Page 12)

DANGER

Wrong selection of motor

Explosion hazard!

▷

Use an original motor or a motor of identical design from the same
manufacturer.

▷

The permissible temperature limits at the motor flange and motor shaft must
be higher than the temperatures generated by the pump. (Contact KSB for
temperatures).

DANGER

Leaks and/or corrosion damage on monitoring systems

No fault indications!

Leakage of fluid handled!

▷

Never install damaged or corroded monitoring systems in the pump.

▷

Check monitoring systems for damage and correct function prior to installation.

WARNING

Improper lifting/moving of heavy assemblies or components

Personal injury and damage to property!

▷

Use suitable transport devices, lifting equipment and lifting tackle to move
heavy assemblies or components.

WARNING

Collision between bearing bracket lantern and containment shroud or bearing
bracket lantern and bearing bracket/intermediate piece due to magnetic forces

Damage to magnets and bearings!

Risk of injury!

▷

Strictly follow the instructions for reassembly.

«
...
57
58
59
60
61
...
»

Summary of Contents for Magnochem-Bloc

































































































Reviews:

No comments

Related manuals for Magnochem-Bloc

Brand: Danfoss Pages: 8

Brand: Aaronia Pages: 47

Brand: SAGEMCOM Pages: 33

Brand: Energic Plus Pages: 12

Brand: AEMC Pages: 4

Veeder-Root 7990 Series

Brand: Danaher Pages: 8

Brand: CONDTROL Pages: 8

Brand: ASCEL Electronic Pages: 64

Brand: THORLABS Pages: 21

Brand: Hilti Pages: 31

Brand: Fly Henry Pages: 5

Sensorex SX41170SI

Brand: Meggitt Pages: 19

Speedrite Fault Finder

Brand: Tru-Test Pages: 2

Brand: PCB Piezotronics Pages: 11

SoundAdvisor NMS045

Brand: Larson Davis Pages: 64

Brand: Tenma Pages: 52

Brand: M&C Pages: 18

Brand: CONDTROL Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands