Korg wavestate native User Manual Download Page 74

Page: 74 / 91

Modulation Processors

Smooth

This creates more gentle transitions between values, smoothing out abrupt changes such as a quick move on a wheel or

a sharp edge on an LFO.
You have separate control of the amount of smoothing during the attack (when the signal is increasing) and decay

(when it’s decreasing).
Low settings provide subtle controller smoothing, creating more gradual aftertouch, for instance. Higher settings create

auto-fade effects, transforming a quick gesture into a longer fade-in and/or fade-out event.
Smoothing can also be used to alter the shape of programmable mod sources, such as LFOs and envelopes. For

instance, you can turn a “blip” into a simple envelope shape, as shown below.

Input

[List of Modulation Sources]

This selects the input for the Mod Processor.

Attack

[0.000…10.000 sec]

This controls how long it takes the smoother to reach a new,

higher value. Higher settings mean longer times.

Decay

[0.000…10.000 sec]

This controls how long it takes the smoother to reach a new, lower

value. Higher settings mean longer times.

Sum

Output

Main Input

Sum Source

Main Input Amount

Sum Source Amount

Sum adds two modulation sources together. This is useful if you want to process the combination of two or more

signals: for instance, to merge an LFO and an envelope, and then smooth the result.

Input

[List of Modulation Sources]

This selects the main input for the Mod Processor.

Main Input Amount

[–100%…+100%]

This controls the gain and polarity of the Input.

Sum Source

[List of Modulation Sources]

This selects the modulation source to merge into the Input.

Sum Source Amount

[–100%…+100%]

This controls the gain and polarity of the Sum Source.

Original Input

Smooth with long Attack
and short Decay

Smooth with short Attack and long Release

Summary of Contents for wavestate native




























































































Search results

Summary of Contents for wavestate native

Reviews:

Related manuals for wavestate native

Brands by name

Popular brands

Korg wavestate native, User Manual

Search results

Summary of Contents for wavestate native

Reviews:

Related manuals for wavestate native

Brands by name

Popular brands