manualshive.com logo in svg

Kontron CP6500-V, User Manual

Share
Download
Kontron CP6500-V User Manual Download Page 162

30

 

 

Chapter 4: PCI/PnP Setup

 

PCI/PnP Setup,

 

Continued

 

 

DMA  

Set this value to allow the DMA setting to be modified. The optimal and Fail-Safe default 
setting is 

Available.

 

 

DMA Channel 

Option 

Description 

 
Available 

 
This setting allows the specified DMA to be used by PCI/PnP device. This is the 
default setting. 

DMA Channel 0 
DMA Channel 1 
DMA Channel 3 
DMA Channel 5 
DMA Channel 6 
DMA Channel 7 

 
Reserved 

 
This setting allows the specified DMA to be used by a legacy ISA device. 
 

 

 

Reserved Memory Size 

Set this value to allow the system to reserve memory that is used by ISA devices. The 
optimal and Fail-Safe default setting is 

Disabled.

 

 

Option Description 

Disabled  

Set this value to prevent BIOS from reserving memory to ISA devices. 

16K 

Set this value to allow the system to reserve 16K of the system memory to the ISA devices. 

32K 

Set this value to allow the system to reserve 32K of the system memory to the ISA devices. 

64K 

Set this value to allow the system to reserve 64K of the system memory to the ISA devices. 

 

 
 
 
 

Summary of Contents for CP6500-V

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands