Kontron CP6500-V User Manual Download Page 149

Page: 149 / 192

Chapter 3: Advanced BIOS Setup

Advanced BIOS Setup,

Continued

Floppy Drive A:

Move the cursor to these fields via up and down <arrow> keys. Select the floppy type.
The Optimal setting for floppy drive A: is

1.44 MB 3½”.

The Fail-Safe setting and the

default setting for drive A: is

Disabled

Option Description

Disabled

Set this value to prevent the use of the selected floppy disk drive channel. This option should be
set if no floppy disk drive is installed on the specified channel.

360 KB 5 ¼”

Set this value if the floppy disk drive attached to the corresponding channel is a 360 KB 5¼“
floppy disk drive.

1.2 MB 5 ¼”

Set this value if the floppy disk drive attached to the corresponding channel is a 1.2 MB 5¼“
floppy disk drive.

720 KB 3 ½”

Set this value if the floppy disk drive attached to the corresponding channel is a 720 KB 3½“
floppy disk drive.

1.44 MB 3 ½”

Set this value if the floppy disk drive attached to the corresponding channel is a 1.44 MB 3½“
floppy disk drive. This is the default setting for

Floppy Drive A

Summary of Contents for CP6500-V

































































































































































































Search results

Summary of Contents for CP6500-V

Reviews:

Brands by name

Popular brands

Kontron CP6500-V, User Manual

Search results

Summary of Contents for CP6500-V

Reviews:

Brands by name

Popular brands