manualshive.com logo in svg

Kontron CP6500-V, User Manual

Share
Download
Kontron CP6500-V User Manual Download Page 153

 

 

 

Chapter 3: Advanced BIOS Setup 

 

21 

 

Advanced BIOS Setup,

 

Continued

 

 

Advanced ACPI Configuration 

You can use this screen to select options for the ACPI Advanced Configuration Settings. 
Use the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys 
to change the value of the selected option. A description of the selected item appears on 
the right side of the screen. The settings are described on this page. The screen is shown 
below. 
 

 

 

ACPI 2.0 Feature 

Set this value to allow or prevent the system to be complaint with the ACPI 2.0 
specification. 
 

Option Description 
No 

This setting prevents the BIOS from supporting the ACPI 2.0 specification. 

Yes 

This setting allows the BIOS to support the ACPI 2.0 specification. 

 

 
ACPI APIC Support 

Include ACPI APIC table pointer to RSDT pointer list.  
 

 
AMI OEMB Table 

Include OEMB table pointer to R(X)SDT pointer list 

 

 

 

 
 

Summary of Contents for CP6500-V

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands