manualshive.com logo in svg

Kontron CP6500-V, User Manual

Share
Download
Kontron CP6500-V User Manual Download Page 129

 

 

Preface  

iii

 

Table of Contents 

Limitations of Liability ................................................................................................................ii

 

Trademarks ...............................................................................................................................ii

 

Table of Contents......................................................................................................................... iii

 

Chapter 1

 

Starting CP6500-V ................................................................................................1

 

Starting CP6500-V ........................................................................................................................1

 

CP6500-V Setup Menu .................................................................................................................2

 

Navigation .....................................................................................................................................2

 

Navigation, Continued...................................................................................................................4

 

Chapter 2

 

Main Setup.............................................................................................................5

 

System Time/System Date ...........................................................................................................5

 

Chapter 3

 

Advanced BIOS Setup..........................................................................................7

 

Advanced BIOS Setup ..................................................................................................................8

 

CPU CONFIGURATION SCREEN............................................................................................8

 

CPU Configuration Settings ......................................................................................................8

 

Advanced BIOS Setup, Continued................................................................................................9

 

IDE CONFIGURATION SCREEN .............................................................................................9

 

IDE Configuration Settings ........................................................................................................9

 

IDE Configuration ......................................................................................................................9

 

Advanced BIOS Setup, Continued............................................................................................. 10

 

Onboard PCI IDE Controller................................................................................................... 10

 

Primary IDE Master, Primary IDE Slave, Secondary IDE Master, Secondary IDE Slave...... 10

 

Hard disk drive Write Protect.................................................................................................. 10

 

IDE Detect Time Out (Seconds)............................................................................................. 10

 

Advanced BIOS Setup,

 

Continued............................................................................................. 11

 

ATA (PI) 80 pin Cable Detection ............................................................................................ 11

 

Advanced BIOS Setup,

 

Continued............................................................................................. 12

 

PRIMARY AND SECONDARY IDE MASTER AND SLAVE SUB MENU .............................. 12

 

Primary and Secondary IDE Master and Slave Settings ....................................................... 12

 

Drive Parameters.................................................................................................................... 12

 

Advanced BIOS Setup,

 

Continued............................................................................................. 13

 

Type........................................................................................................................................ 13

 

LBA/Large Mode..................................................................................................................... 13

 

Advanced BIOS Setup,

 

Continued............................................................................................. 14

 

Block (Multi-Sector Transfer).................................................................................................. 14

 

PIO Mode ............................................................................................................................... 14

 

DMA Mode.............................................................................................................................. 14

 

Advanced BIOS Setup,

 

Continued............................................................................................. 15

 

S.M.A.R.T. for Hard disk drives.............................................................................................. 15

 

32Bit Data Transfer ................................................................................................................ 15

 

ARMD Emulation Type........................................................................................................... 15

 

Advanced BIOS Setup,

 

Continued............................................................................................. 16

 

FLOPPY CONFIGURATION SCREEN.................................................................................. 16

 

Floppy Configuration Settings ................................................................................................ 16

 

Advanced BIOS Setup,

 

Continued............................................................................................. 17

 

Floppy Drive A: ....................................................................................................................... 17

 

Advanced BIOS Setup,

 

Continued............................................................................................. 18

 

SUPER IO CONFIGURATION SCREEN............................................................................... 18

 

SuperIO Configuration Screen ............................................................................................... 18

 

Advanced BIOS Setup,

 

Continued............................................................................................. 19

 

Onboard Floppy Controller ..................................................................................................... 19

 

Serial Port1 Address .............................................................................................................. 19

 

Summary of Contents for CP6500-V

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands