Kontron CP6500-V User Manual Download Page 130

Page: 130 / 192

Preface

Serial Port2 Address .............................................................................................................. 19

Advanced BIOS Setup,

Continued............................................................................................. 20

ACPI CONFIGURATION........................................................................................................ 20

ACPI Aware O/S..................................................................................................................... 20

Advanced BIOS Setup,

Continued............................................................................................. 21

Advanced ACPI Configuration................................................................................................ 21

ACPI 2.0 Feature.................................................................................................................... 21

ACPI APIC Support ................................................................................................................ 21

AMI OEMB Table.................................................................................................................... 21

Advanced BIOS Setup,

Continued............................................................................................. 22

EVENT LOG CONFIGURATION............................................................................................ 22

View Event Log....................................................................................................................... 22

Mark all events as read .......................................................................................................... 22

Mark all unread events as read and clear the Event Log buffer. ........................................... 22

Clear Event Log...................................................................................................................... 22

Discard all events in the Event Log........................................................................................ 22

Event Log Statistics................................................................................................................ 22

PCI Error Logging................................................................................................................... 22

Advanced BIOS Setup,

Continued............................................................................................. 23

REMOTE ACCESS CONFIGURATION................................................................................. 23

Remote Access Configuration................................................................................................ 23

Remote Access ...................................................................................................................... 23

Advanced BIOS Setup,

Continued............................................................................................. 24

Serial Port Number................................................................................................................. 24

Serial Port Mode..................................................................................................................... 24

Advanced BIOS Setup,

Continued............................................................................................. 25

USB CONFIGURATION......................................................................................................... 25

USB Configuration.................................................................................................................. 25

USB Function ......................................................................................................................... 25

USB 2.0 Controller Mode ....................................................................................................... 25

USB Mass Storage Device Configuration .............................................................................. 25

Chapter 4

PCI/PnP Setup.................................................................................................... 27

Plug and Play O/S .................................................................................................................. 27

PCI/PnP Setup, Continued ........................................................................................................ 28

PCI Latency Timer.................................................................................................................. 28

Allocate IRQ to VGA............................................................................................................... 28

Palette Snooping .................................................................................................................... 28

PCI/PnP Setup,

Continued......................................................................................................... 29

PCI IDE BusMaster ................................................................................................................ 29

OffBoard PCI/ISA IDE Card ................................................................................................... 29

IRQ ......................................................................................................................................... 29

PCI/PnP Setup,

Continued......................................................................................................... 30

DMA........................................................................................................................................ 30

Reserved Memory Size .......................................................................................................... 30

Chapter 5

Boot Setup.......................................................................................................... 31

Boot Setup, Continued............................................................................................................... 32

BOOT SETTINGS CONFIGURATION................................................................................... 32

Boot Settings Configuration.................................................................................................... 32

Quick Boot .............................................................................................................................. 32

Add-On ROM Display Mode................................................................................................... 32

Boot Setup, Continued............................................................................................................... 33

Boot up Num-Lock.................................................................................................................. 33

PS/2 Mouse Support .............................................................................................................. 33

Wait for ‘F1’ If Error ................................................................................................................ 33

Summary of Contents for CP6500-V

































































































































































































Search results

Summary of Contents for CP6500-V

Reviews:

Brands by name

Popular brands

Kontron CP6500-V, User Manual

Search results

Summary of Contents for CP6500-V

Reviews:

Brands by name

Popular brands