Kontron COMe-bKL6, User Manual

Page: 51 / 95

COMe-bKL6 – User Guide Rev.1.2
www.kontron.com // 51
Pin COMe Signal Description Type Termination Comment
A80 GND Power ground
PWR GND
A81 LV LVDS Channel A clock or EDP lane 3 transmit DP-O Clock 20 MHz to 80 MHz
A82 LVDS_A_CK-
A83 LVDS_I2C_CK I2C Clock for LVDS display use or eDP AUX + I/O-3.3 PU 2.2 k Ω , 3.3 V
(S0)
A84 LVDS_I2C_DAT I2C Data line for LVDS display use or eDP AUX - I/O-3.3 PU 2.2 k
Ω
, 3.3 V
(S0)
A85 GPI3 General purpose input 3 I-3.3 PU 100 k
Ω
3.3 V
(S0)
A86 RSVD Reserved for future use NC
A87 eDP_HPD Detection of Hot Plug / unplug I-3.3 PD 400 k
Ω
LVDS
/ 100 k
Ω
EDP
A88 PCIE Reference PCI Express clock for all PCI Express and
PCI Express graphics lanes DP-O 100 MHz
A89 PCIE_CK_REF-
A90 GND Power ground PWR GND
A91 SPI_POWER 3.3 V power output for external SPI Flash
O-3.3 100 mA maximum
Only use to power SPI
devices on Carrier Board.
A92 SPI_MISO Data in to module from carrier SPI
(SPI Master IN Slave Out) I-3.3 PU 15 k Ω to
40 k
Ω
in PCH
All SPI signals tri-stated
until reset deasserted.
A93 GPO0 General purpose output 0 O-3.3 PD 100 k
Ω
A94 SPI_CLK Clock from module to carrier SPI O-3.3 PU 15 k
Ω
to
40 k
Ω
in PCH
(S5)
All SPI signals tri-stated
with 20 K
Ω
CPU internal
weak pull-up until reset
deasserted.
A95 SPI_MOSI Data out from module to carrier SPI O-3.3 PU 15 k
Ω
to
40 k
Ω
in PCH
(S5)
A96 TPM_PP TPM physical presence I-3.3
PD 10 k
Ω
TMP does not use this
functionality.
A97 TYPE10# Indicates to carrier board that Type 10 module is
installed NC
A98 SER0_TX Serial port 0 TXD O-3.3 20 V protection circuit
implemented on-module,
PD on carrier boards
needed for proper
operation.
A99 SER0_RX Serial port 0 RXD I-5T PU 47 k
Ω
, 3.3 V
(S0)
20 V protection circuit
implemented on-module.
A100 GND Power ground PWR GND
A101 SER1_TX Serial port 1 TXD O-3.3 20 V protection circuit
implemented on-module,
PD on carrier board
needed for proper
operation.
A102 SER1_RX Serial port 1 RXD I-5T
PU 47 k
Ω
, 3.3 V
(S0)
20 V protection circuit
implemented on-module.
A103 LID# LID switch input I-3.3
PU 47 k
Ω
, 3.3 V
(S5)
A104 VCC_12V Main input voltage (4.75 V - 20V) PWR
4.75 V -
20 V
A105 VCC_12V
A106 VCC_12V
A107 VCC_12V
A108 VCC_12V
A109 VCC_12V
A110 GND Power ground PWR GND
+ and - Differential pair differentiator