background image

Important Notice 

 

CVS-705D/707D 

 

ii 

 

0092607052-03 

Important Notice 
 

 

For  copy  and  transcription  of  this  Installation  Manual  (hereinafter  referred  to  as  this  manual), 

permission from Koden is needed. Koden prohibits the un-authorized copy and transcription of this 
manual. 

 

If this manual is lost or damaged, consult a dealer of Koden or Koden. 

 

The  specification  of  the  products  and  the  contents  in  this  manual  are  subject  to  change  without 
notice. 

 

The  contents  displayed  on  the  menu  of  product  may  be  different  from  the  expression  of  this 
manual. The fonts and shapes of the keys and menus in the illustration may differ from the actual 
ones, and some parts may be omitted. 

 

Koden is not liable for damages and troubles arisen from misunderstanding of the contents in this 
manual. 

 

Koden is not liable for any damages caused by earthquake, lightning, wind and flood damage and 
fire for which Koden is not responsible,  and  actions by  third parties, other accidents

, customer’s 

unintended error/abuse and the use under other abnormal conditions. 

 

Koden  is  not  liable  for  damages  of  accompaniment  (change/loss  of  memorized  content,  loss  of 
business profit, stop of business) arisen from use or failure of our products. 

 

If the stored data are changed or lost, irrespective of causes of troubles and damages, Koden is 
not liable for them. 

 

Koden is not liable for any  damages arisen from malfunction caused by combination of software 
and connected equipment in which Koden is not engaged

 
 

Summary of Contents for CVS-705D











































































Reviews: