Koden CVS-705D Installation Manual Download | Manualshive

Page: 47 / 74

background image

CVS-705D/707D

Chapter 1 Installation

0092607052-03

1-27

1.8 Connection of Hemisphere V102 GPS Compass / ComNav

Vector G1 GPS Satellite Compass

This is to describe the connection of Hemisphere V102 GPS Compass / ComNav Vector G1
GPS Satellite Compass used as GPS compass and Heaving sensor.
Refer to the installation manual of the Hemisphere V102 GPS Compass / ComNav Vector G1
GPS Satellite Compass for details of installation.

1.8.1 Connection of Hemisphere V102 GPS Compass / ComNav Vector G1 GPS

Satellite Compass

Connect CW-376-5M by soldering with the cable of Hemisphere V102 GPS Compass /
ComNav Vector G1 GPS Satellite Compass. (Hereafter referred to as

“V102 GPS Compass” )

Please prepare two CW-376-5M when connecting with Radar as GPS compass.

1) The terminal of the cables of V102 GPS Compass is not processed, and 8 lead wires and

1 shield wire are open. Brown and blue lead wires are connected to TX/RX of Port A, white
and green lead wires are connected to TX/RX of Port C, black and red lead wires are
connected to +/- of power supply, and yellow lead wire is connected with earth. Orange
lead wire and shield wire are unconnected.

Refer to the

“Connection of V102 GPS Compass”

, and solder CW-376-5M with Port A

and  power  supply  of  cable  of  Hemisphere  V102  GPS  Compass.  Please  solder  another
CW-376-5M  with  Port  C,  when  connecting  with  Radar  as  GPS  compass.  Please  branch
yellow  wire  (GND)  of  the  cable  of  V102  GPS  Compass  into  four,  two  of  which  shall  be
soldered with each black (RX-) and red (TX-) of CW-376-5M. After soldering is completed,
be sure to process the connected part by self-adhesive tape etc to be water resistant and
insulated.

Connection of V102 GPS Compass

CW-376-5M

Cable of V102 GPS Compass

Blue and shield

White

Orange

Green

Red

Black

Red

Black

White

Orange

Black

Brown

Blue

Red

Yellow

Yellow

Yellow

Yellow

Green

White

Orange

Shield

To NMEA terminal of Radar

CW-376-5M

S

ol

de

re

d

To J3 connector of

CVS-705D/707D

Port A/Power

Port C

Yellow wire is branched into 4.

Unconnected

S

ol

de

re

d

«
...
45
46
47
48
49
...
»

Summary of Contents for CVS-705D











































































Reviews:

No comments

Related manuals for CVS-705D

Brand: Zetec Pages: 23

WJHD309A - DIGITAL DISK RECORDER

Brand: Panasonic Pages: 79

Brand: idiag Pages: 10

Brand: Bandit Pages: 136

Versaflo S Series

Brand: 3M Pages: 11

DBI Sala EXOFIT

Brand: 3M Pages: 32

Brand: 3M Pages: 8

Brand: Accurate Bio-Medical Technology Pages: 35

Brand: e+p Elektrik Handels Pages: 2

Brand: DBX Bushido Pages: 12

Brand: Gardena Pages: 19

Brand: Jackco Pages: 6

Brand: EuroLite Pages: 28

Brand: Launch Pages: 3

Brand: Launch Pages: 43

Brand: Launch Pages: 8

Brand: Launch Pages: 67

Brand: Launch Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands