manualshive.com logo in svg

Kingfisher 2525, Ownersmanual, Page: 64 / 69

Share
Download
Kingfisher 2525 Ownersmanual Download Page 64

KINGFISHER 

O W N E R ’ S   M A N U A L  

 

w w w . k i n g f i s h e r b o a t s . c o m  

 

61 

Cold Air Defroster

 

The cold air defroster fan is located either on the inside of the dash support leg or behind 
a carpeted panel directly below the dash foot rest. 
 

 

 

 

 

 

Cold air defroster fan 

To operate the fan: 

  Ensure that the battery power is turned on. 

  Open and direct the dash mounted defroster vents  

 

      

Defroster vents 

 

  Turn on the fan switch located to the left hand side of the steering wheel 

 

If the cold air defroster fails to work: 

  Confirm that the battery switch is turned on 

  Confirm that the battery system is fully charged and functioning and that all wires 

leading to the batteries are secured firmly to the battery posts 

  Check that the main 30amp battery fuse has not blown 

  Check that the blower fuse underneath the dash has not blown 

  Once that all the above has been checked, if the blower is still not operating, 

consult your authorized Kingfisher dealer 

 

Summary of Contents for 2525






































































Reviews:

No comments