Kingfisher 2525 Ownersmanual Download Page 6 | Manualshive

Page: 6 / 69

Kingfisher 2525 Ownersmanual Download Page 6

KINGFISHER

O W N E R ’ S M A N U A L

w w w . k i n g f i s h e r b o a t s . c o m

3

IMPORTANT LABELS AND WARNINGS`

General Information

Your boat is supplied with a number of identification and warning labels. These labels are
intended to inform and protect the boat operator and passengers. Should any of these
labels be damaged or lost they should be replaced immediately. Failure to comply with
the warnings can result in severe injury or death. Should you need replacement warning
labels, conformity/capacity labels, or instruction labels, contact your dealership. Each label
carries a Westwinn part number for easy identification.

Warning Labels

Be sure to familiarize yourself with the following warning labels:

NOTE:

Not all models may carry all Warnings, depending on the options chosen.

Decal 1:

Is located in the starboard side rear deck tray and relates to the shore power
system.

The Carbon Monoxide (CO) warning decal is located on the rear bait well.

The fuel system inspection decal is located inside the bilge doors.

The boarding ladder warning label is located on the rear swim platform.

Decal 2:

The auxiliary and main engine operation warning decal is located above the
auxiliary steering station.

Decal 3:

The winterization warning decal is attached to the sink faucet and should be
removed after the system is flushed.

Decal 4:

The blower warning label is used on diesel inboard models only, and is
installed on the starboard side of the engine box.

Decal 5:

The auxiliary station visibility warning label is located above the rear helm
station.

Decal 6:

The water pickup shutoff label is located by the thru-hull petcock in the
headstall, beside the toilet

Decal 7:

The Watertight Closure decal is located near all doors or hatches which
should be kept closed while underway, such as the cabin door.

Decal 8:

The Transport Canada Conformity Label is located on the baitwell at the
stern of the boat.

Decal 9:

The US Coast Guard Conformity Label is located on the baitwell at the stern
of the boat.

DO NOT remove any of the safety decals!

«
...
4
5
6
7
8
...
»

Summary of Contents for 2525






































































Reviews:

No comments