manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 98 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 98

 98 

Ver 5, pg 190, fig 42.2 update

Ver 5, pg 190, fig 42.3 update

Ver 5, pg 190, fig 42.2 update

Ver 5, pg 190, fig 42.3 update

Step 52: Attach Swings

Threaded 

Quick Link

A:

  Using 1 Threaded Quick Link per rope, join the Acro Rope to the Acro Bar . Using another Threaded Quick 

Link, attach the Acro Handle to the Acro Bar . Make sure to close the Threaded Quick Link tightly using an 

adjustable wrench. (fig. 52.2 and 52.3)

B:

  Attach the the swing and acro the Quick Links attached to the Swing Hangers. (fig. 52.1)

Tighten 

Threaded Link 

using adjustable 

wrench

Threaded Link 

attach to Swing and 

Acro ropes .

Acro Bar

Acro Handles

Quick Link

Acro Rope 

& Chain

Other Parts

Fig. 52.2

Fig. 52.3

Fig. 52.1

Caution:  Threaded Quick Links must be 

installed with the gate completely down 

covering the threads and tighten as 

instructed. (fig. 52.2)

1 x Acro Bar

2 x Acro Handle

2 x Acro Rope & Chain

4 x Threaded Quick Link

2 x Long Belt Swing w Chain

Threaded 

Quick Link

Acro Rope

Quick Link

Swing Belt Seat

Swing Ropes 

w/crimps

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments