manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 34 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 34

 34 

2 x 

Side Floor Joist 1-1/2 x 1-1/2 x 62-13/64”

2 x 

Side Joist 1-1/2 x 1-1/2 x 21-15/32”

Wood Parts

9356

9382

8 x 

#8 x 2-1/2” Wood Screw

8 x 

5/16 x 2-5/8” Wafer Bolt

 

(FW2, TN2)  

Hardware

S3

WB10

front wall 

hidden for 

clarity

NOTE hole 
orientation

Fig. 7.5

9356

Panel

or

5/8”

 

(16mm)

Fig. 7.4

9382

front wall 

hidden for 

clarity

front wall hidden 
for clarity

Fig. 7.2

9356

9002

9382

9451

9362

NOTE:  hole orientation

S3

x 4 per 

side

x 4 per 

side

WB10

9356

Fig. 7.3

9356

9382

S3

WB10

C: 

From inside the assembly, tight to the Front Wall Panel, measure 5/8” (16mm) down from the center of the 

panel assembly and loosely attach 1 (9356) Side Floor Joist to Front Wall Panel using 3 (WB10) 5/16 x 2-5/8” 

Wafer Bolts (with flat washer and t-nut), making sure that it’s tight to the (9214) End Slide Panel. Bolts are 

installed from inside the assembly. (fig 7.2, 7.3, 7.4 and 7.5)

D: 

Place (9382) Side Joist so that it fits between the (9356) Side Floor Joist and (9213) SW Wall Panel and 

loosely attach using 1 (WB10) 5/16 x 2-5/8” Wafer Bolt (with flat washer and t-nut). (fig 7.2, 7.3, 7.4 and 7.5)

E: 

Make sure (9356) Side Floor Joist and (9382) Side Joist are level then attach with 2 (S3) #8 x 2-1/2” Wood 

Screws per joist and tighten bolts. (fig 7.2, 7.3 and 7.5)

F: 

Repeat Steps B - D to install (9356) Side Floor Joist and (9382) Side Joist to the Back Wall Panel . 

9213

9214

Step 7:  Join Swing and Slide Assemblies   

Part 2

TN2

FW2

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments