manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 65 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 65

 65 

Step 25: Attach Soffits

2 x 

Soffit 5/8 x 4-27/64 x 40-5/32”

2 x 

Soffit Narrow 15.9 x 1-19/32 x 43-11/32”

Wood Parts

Hardware

9350

9351

18 x 

#8 x 1-3/8” Wood Screw

S20

Fig. 25.1

Fig. 25.2

   Flush

9350

A:

 On the top of the Front Wall place 1 (9350) Soffit so that it’s centered over (9365) TB Support and flush to the 

inside edge, making sure to follow the hole orientation closely. Using the inside set of holes, attach (9350) Soffit 

with 6 (S20) #8 x 1- 3/8” Wood Screws. (fig 25.1 and fig 25.2)

B:

 Repeat Step A to install (9350) Soffit on the Back Wall Panel. (fig 25.1)

C:

 Place 1 (9351) Soffit Narrow across the end of each opening so they are flush and tight to the (9351) Soffits. 

Attach (9351) Soffit Narrow on the SW Wall Panel side using 4 (S20) #8 x 1- 3/8” Wood Screws and on the 

opposite side using 2 (S20) #8 x 1- 3/8” Wood Screws taking care to ensure that the correct pre-drilled holes are 

being used .  (fig 25.1 and fig 25.2)

S20

x 2

9350

9351

S20

S20

per side

x 6

9351

9365

S20

SW Wall 

Panel

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments