manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 21 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 21

 21 

Wood Parts

Other Parts

Hardware

x 7 per window

S0

S0

H10

MOD 5 Pane 

Window

x 2

WB1

x 4

14 x 

# 8 x 7/8 Truss Head Screw 

4 x 

5/16 x 1” Wafer Bolt  (FW2, TN2)

2 x 

1/4 x 2-1/4” Hex Bolt (LW1, FW1, TN1)

H10

WB1

S0

9377

9367

9451

9363

9361

9372

9362

9369

9353

1 x 

Base End Post 1-1/4 x 2-1/4 x 86-29/32”

1 x 

Narrow Mid Cross - Front 1-1/4 x 3 x 22-5/16”

1 x 

Cross Support Middle Short 1-1/4 x 3 x 20-13/16” 

1 x 

Window Brace 1-1/4 x 3 x 8”

2 x MOD 5 Pane Window

9451

9367

9377

9363

Step 2:  Front Wall Assembly 

Part 3

Fig. 2.5

Fig. 2.6

H:

  Place 2 MOD 5 Pane Windows in the upper openings and attach to frame assembly using 7 (S0) #8 x 7/8” 

Truss Head Screws per window . (fig. 2.5, 2.7 and 2.8) 

I:

  Place (9377) Window Brace over the pre-drilled holes in (9353) Cross Support Top and (9369) Left Upright Front 

to join the sections. Attach using 2 (H10) ¼ x 2- ¼” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 2.5)

J:

  Loosely attach (9363) Base End Post to (9372) Cross Frame using 1 (WB1) 5/16 x 1” Wafer Bolt (with flat 

washer and t-nut). (fig. 2.6)

K:

  Place 1 (9451) Cross Support Middle Short over the center hole in (9363) Base End Post and 1 (9367) Narrow 

Mid Cross Front over the top hole. Loosely attach boards using 4 (WB1) 5/16 x 1” Wafer Bolts (with flat washer and 

t-nut) in the locations shown in fig. 2 .6 .

S0

S0

Fig. 2.7

Fig. 2.8

TN2

TN1

FW2

FW1

LW1

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments