manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 74 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 74

 74 

2 x 

Heavy SW Post 2 x 3 x 86-11/16”

1 x 

SW Upright 3 x 3 x 50-15/16”

1 x 

SW Support 15/16 x 3-1/4 x 46-1/2”

Step 30: Swing End Assembly

A:

  Loosely attach 2 (2613) Heavy SW Posts to (2615) SW Upright using 2 (G7) 5/16 x 5-1/2” Hex Bolts (with 

lock washer, flat washer and t-nut). Notice 2 bolt holes at top of (2615) SW Upright and orientation of angle. 

(fig. 30.1) 

B:

  Attach (2616) SW Support to both (2613) Heavy SW Posts and (2615) SW Upright using 3 (G4) 5/16 x 4” 

Hex Bolts (with lock washer, flat washer and t-nut). Tighten all bolts.  (fig. 30.1)  

C:

  Install 2 (WB7) 5/16 x 3” Wafer Bolts (with flat washer and t-nut) in the top bolt holes in (2615) SW Upright 

as shown in fig. 30.1. 

IT IS IMPORTA NT THAT THESE BOLTS ARE ATTACHED. THEY WILL MINIMIZE 

CHECKING OF WOOD.

Hardware

Wood Parts

2 x 

Hex Bolt 5/16 x 5-1/2” (LW2, FW2, TN2)

3 x 

Hex Bolt 5/16 x 4” (LW2, FW2, TN2)

2 x 

Wafer Head Bolt 5/16 x 3” (FW2 & TN2)

G7

WB7

G4

Notice 2 bolt 

holes at top and 

orientation of 

the angle

WB7

Fig. 30.1

2613

2615

2613

2615

2616

G7

2616

G4

TN2

TN2

TN2

FW2

FW2

FW2

LW2

LW2

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments