manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 46 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 46

 46 

16 x 

 #8 x 2” Wood Screw

Hardware

S11

S11

S11

2 x 

Short Bottom 1-1/4 x 2 x 20-5/8”

4 x 

Tower Roof Support 1-5/16 x 2-5/16 x 23-5/8”

Wood Parts

9459
9380

9459

9460

9379

9379

9380

x 2 per 

side

x 2 per 

side

B:

 Place (9459) Short Bottoms across the front and back of the tower assembly so they are flush to the tops of 

(9460) Wall Supports and (9379) Soffits. Attach from the outside of (9379) Soffits using 4 (S11) #8 x 2” Wood 

Screws per board. (fig 14.2)

C:

 On the front and back of the tower assembly install 2 (9380) Tower Roof Supports between the (9459) Short 

Bottoms and the (9248) Narrow Panels so they are flush and tight to the (9460) Supports. Attach using 2 (S11) #8 x 

2” Wood Screws per board. (fig 14.2)

Step 14: Tower Roof Support Assembly   

Part 2

Fig. 14.2

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments