manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 88 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 88

 88 

V5, pg 180, fig 32.1 update image

* take inside view 

from an existing 

instruction

* take inside view 

from an existing 

instruction

Step 42: Attach Flange Assembly to Fort

Hardware

14 x 

#12 x 1”  Pan Screw

4 x 

#12 x 2”  Pan Screw

8 x  

#12 Screw Bezel

S7

S6

FW6

flush to top of 

the (9214) End 

Slide Panel

flush to bottom 

of the (9214) End 

Slide Panel

Fig. 42.1

Fig. 42.3

Fig. 42.2
Outside View

Inside View

A:  

With a helper place the Flange Assembly flush to the top opening in (9214) End Slide Panel as shown in fig. 

42.1 & 42.2, then pre-drill 1/8” pilot holes in the bottom 4 mounting locations (approximate spots where circles 

are on figure), making sure the pre-drilled holes are a minimum of 2.5 cm (1”) deep. (fig. 42.1) 

B: 

Attach Flange Assembly to bottom of (9214) End Slide Panel opening using 4 (S7) #12 x 2” Pan Screws 

(with #12 Screw Bezel) in the pre-drilled holes. (fig. 42.1) Make sure the flat surfaces of the Flange Assembly 

are flush to the (9214) End Slide Panel as shown in fig. 42.3. 

C: 

Attach the Flange Assembly flush to top of (9214) End Slide Panel opening using 4 (S6) #12 x 1” Pan 

Screws (with #12 Screw Bezel) as shown in fig. 42.1 and to both sides using 5 (S6) #12 x 1” Pan Screws per 

side. (fig. 42.1)

9214

Lower SL Insert 

the 4 holes need 

to be pre-drilled

side

side

S6

x 5

w/ #12 

Screw Bezel

w/ #12 

Screw Bezel

S7

S6

x 5

S6

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments