manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 56 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 56

 56 

1 x 

Left Rail 1-3/8 x 2-1/2 x 57-53/64”

1 x 

Right Access 1-3/8 x 2-1/2 x 57-53/64”

4 x 

Tread 15/16 x 3-1/4 x 19-1/2”

8957

9055

9239

Fig. 20.1

Wood Parts

Hardware

Step 20: Access Ladder / Rockwall Assembly 

Part 1

A:

 Place (9239) Left Rail on one side of 4 (8957) Treads and (9055) Right Access on the other side with the 

grooves facing in. (fig. 20.1) 

B:

 Fit each (8957) Tread into grooves on both (9239) and (9055) Access rails, making sure the top edge of the 

(8957) Treads are flush to the front of the Access rails. (fig. 20.1 and 20.2) 

C:

 Pre-drill pilot holes with a 1/8” drill bit and attach rails and treads together using 4 (S3) #8 x 2-1/2” Wood 

Screws per tread .

16 x 

#8 x 2-1/2” Wood Screw

S3

Fig. 20.2
End View

Flush to 

edges

Top Edge of Access Rail

S3

S3

8957

9239

9055

Flush to 

top edge

8957

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments