manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 58 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 58

 58 

1 x 

Access Rock Bottom 5/8 x 5-1/4 x 22-1/8” 

1 x 

Access Board 5/8 x 4-1/4 x 22-1/8”

4 x 

Board Rock A 5/8 x 5-1/4 x 22-1/8”

5 x 

Board Rock B 5/8 x 5-1/4x 22-1/8”

Wood Parts

Hardware

8515

8512

8511

9032

A: 

Place (9032) Access Board flush to the top of the Access Ladder/Rockwall Assembly and (8515) Access Rock 

Bottom at the bottom of the assembly as shown in fig. 21.1. Then place (8511) Board Rock A and (8512) Board 

Rock B as shown in fig. 21.1. Do not screw boards down yet. Rock holes are to be staggered so they do not form 

a straight line and are at the top of the boards . 

Note: Rock Boards are to be flush to (9055) Right Access and 

pilot holes are centered over (9058) Rock Rail.

 (fig. 21.1) 

B: 

Make sure all boards are tight together and the assembly is square, then attach all boards except for (9032) 

Access Board using 4 (S20) #8 x 1-3/8” Wood Screws per board . (9032) Access Board to be attached in Step 22, 

Part 2, keep aside until needed .

40 x 

#8 x 1-3/8” Wood Screw

Fig. 21.1

S20

IMPORTANT! 

Follow hole pattern

x 4 per 

board

S20

Do not attach yet, 

put aside until 

Step 22, Part 2

9032

8511

8511

8511

8511

8512

8512

8512

8512

8512

8515

Flush

9239

9055

9058

Step 21: Rockwall Assembly  

Part 1

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments