manualshive.com logo in svg

KidKraft Cedar Summit DEVONSHIRE ELITE, Installation And Operating Instructions Manual, Page: 35 / 100

Share
Download
KidKraft Cedar Summit DEVONSHIRE ELITE Installation And Operating Instructions Manual Download Page 35

 35 

Hardware

Wood Parts

1 x  

Center Floor Joist 1-1/4 x 3 x 62-13/64”   

 

1 x 

Floor Board 5/8 x 3-3/8 x 34-3/8”

1 x 

Center floor support 1-1/4 x 3 x 34-3/8”

6 x 

#8 x 3” Wood Screw

6 x          #8 x 1-3/8” Wood Screw

9357

S4

S20

9359

9462

S4

9462

front wall hidden 

for clarity

place floor board to set height

front wall hidden 

for clarity

9359

9357

9462

S4

S20

S4

x 6

Fig. 8.2

Fig. 8.1

9356

9382

9213

A: 

Place 1 (9359) Floor Board tight to (9213) SW Wall Panel and attach to the (9382) Side Joists with 4 (S20) #8 x 

1-3/8” Wood Screws. (fig. 8.1)

B: 

Have a helper hold (9356) Center Floor Joist tight to the bottom of (9359) Floor Board and centered over the pilot 

holes in the (9213) SW Wall Panel. Attach from outside of the assembly using 2 (S4) #8 x 3” Wood Screws. (fig. 8.1)

C: 

Place (9462) Center Floor Support across the opposite end of (9357) Center Floor Joist, making sure that both 

boards are flush at the top. Attach (9462) Center Floor Support to (9357) Center Floor Joist with 2 (S4) #8 x 3” 

Wood Screws. (fig 8.1 and 8.2)

D: 

Check to make sure joist assembly is level, then from underneath attach (9462) Center Floor Support to each 

(9356) Side Floor Joist using 1 (S4) #8 x 3” Wood Screw per side. (fig 8.1 and 8.2)

E: 

Attach (9359) Floor Board to (9357) Center Floor Joist using 2 (S20) #8 x 1- 3/8” Wood Screws. (fig. 8.1)

Step 8:  Floor Assembly   

Part 1

Summary of Contents for Cedar Summit DEVONSHIRE ELITE





































































































Reviews:

No comments