Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
5
Adder Worksurface
Note:
The adder worksurface
is assembled upside down, and
when turned upright after full
assembly, it will attach to the
worksurface to its right (either
starter or adder as the user sits
at it).
5. As in step 1, Figure 1 earlier,
begin assembly by installing
two shared-leg brackets to a
transitional leg set (leg with
shorter foot). Use three
#10 x ½” screws per bracket to
secure (Figure 1).
6. To avoid scratching top, carefully
lay adder worksurface upside
down on a soft, protective
surface. Install the transitional
leg set to the underside of the
worksurface at pre-drilled holes
using four #12 x 1” screws.
The transitional leg set will be
“shared” so should be installed
to the mounting holes closest to
the edge of the worksurface such
that the centerline of the leg is
directly over the end of the table
(Figure 2).
Note:
Adder modesty panels are
longer than “starter” modesty
panels.
7. Position an adder modesty
over the mounting holes in
worksurface, and next to the
transitional leg as illustrated.
If optional horizontal wireway
is to be installed to unit, place
the wireway between mounting
flange of modesty panel and
the worksurface, aligning the
mounting holes as illustrated.
Secure modesty panel to
worksurface with three #12 x 1”
screws, and attach one modesty
panel end to the transitional
leg using two #10 x ½” screws
(Figure 2).
WorkZone
®
Starter/Adder/Finisher Worksurface
Assembly Instructions
Adder Worksurface
Note:
Note:
The adder worksurface is assembled
upside down, and when turned upright after
full assembly, it will attach to the worksurface
to its right (either starter or adder as the user
sits at it).
5. As in step 1, Figure 1 earlier, begin
assembly by installing two shared-leg
brackets to a transitional leg set (leg with
shorter foot). Use three #10 x ½” screws per
bracket to secure (Figure 1).
6. To avoid scratching top, carefully lay adder
worksurface upside down on a soft,
protective surface. Install the transitional leg
set to the underside of the worksurface at
pre-drilled holes using four #12 x 1” screws.
The transitional leg set will be “shared” so
should be installed to the mounting holes
closest to the edge of the worksurface such
that the centerline of the leg is directly over
the end of the table (Figure 2).
Adder modesty panels are longer than
“starter” modesty panels.
7. Position an adder modesty over the
mounting holes in worksurface, and next to
the transitional leg as illustrated.
Secure modesty panel to worksurface with
three #12 x 1” screws, and attach one
modesty panel end to the transitional leg
using two #10 x ½” screws (Figure 2).
If optional
horizontal wireway is to be installed to unit,
place the wireway between mounting flange
of modesty panel and the worksurface,
aligning the mounting holes as illustrated.
Figure 2 - Adder Worksurface
shared-leg
bracket
#10 x ½”
screw
#12 x 1”
screws
adder
modesty panel
(longer)
adder
worksurface
transitional leg set
(shorter foot)
horizontal
wireway
(optional)
Starter/Adder/Finisher Worksurface Assembly
Figure 2 - Adder Worksurface
