KI WorkZone Assembly Instructions Manual Download Page 28 | Manualshive

Page: 28 / 36

KI WorkZone Assembly Instructions Manual Download Page 28

28

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.

Tools Required

•

Phillips Screwdriver

•

Level

1. Set the peninsula worksurface

face down onto a soft

protective surface. Attach the

single leg to the peninsula

worksurface with four #12 x 1”

screws (Figure 1).

2. Align the corner leg with

the pre-drilled holes in the

peninsula worksurface at the

corner opposite from where

the peninsula will attach

the adjoining rectangular

worksurface. Be sure that the

modesty panel mounting holes

on the corner leg face inward

for mounting of the modesty

panel next (Figure 1).

3. Position the side-mount

modesty panel under the

peninsula and align mounting

holes to holes in corner leg.

Secure modesty panel to

corner leg with two #10 x ½”

screws. Attach the modesty

panel to the peninsula with two

#12 x 1” screws (Figure 1).

4. Install a leg plug into each

of the two exposed holes in

the corner leg as illustrated

(Figure 1).

WorkZone

®

Peninsula Worksurface - Side Mouting

Assembly Instructions

#12 x 1" screw

#10 x ½" screw

Tools Required

Phillips Screwdriver
Level

1. Set the peninsula worksurface face down
onto a soft protective surface. Attach the
single leg to the peninsula worksurface with
four #12 x 1” screws (Figure 1).

2. Align the corner leg with the pre-drilled
holes in the peninsula worksurface at the
corner opposite from where the peninsula
will attach the adjoining rectangular
worksurface. Be sure that the modesty panel
mounting holes on the corner leg face
inward for mounting of the modesty panel
next (Figure 1).

3. Position the side-mount modesty panel
under the peninsula and align mounting
holes to holes in corner leg. Secure modesty
panel to corner leg with two #10 x ½”
screws. Attach the modesty panel to the
peninsula with two #12 x 1” screws
(Figure 1).

4. Install a leg plug into each of the two
exposed holes in the corner leg as illustrated
(Figure 1).

#12 x 1" screw

#10 x ½" screw

WorkZone Peninsula Worksurface

Side Mounting

Assembly Instructions

#12 x 1"

screw

#12 x 1"

screw

#12 x 1"

screw

adjustable

glide

adjustable

glide

single

leg

corner

leg

leg

plug

side mount

modesty panel

#10 x / "

screw

1

2

peninsula

worksurface

Figure 1

Figure 1

«
...
26
27
28
29
30
...
»

Summary of Contents for WorkZone





































Reviews:

No comments