KG ELS-304 Operation Manual Download Page 4

Page: 4 / 80

ELS-304

For your safety use of this product

Input Power

Do not input the Volt. other than specified for this product.

(The input rated for this product is AC100V-240V 50/60Hz)

And Do not used the AC Power Cable that is attached to this

product.(Rated of the attached Power Cable in Japan is

AC100V

）

Use the proper cable that meets the Volt. and shapes in

t the area or country.

Fuse

The fuse located in the AC inlet can be changed .

Use the proper Fuse with the same shape, rated, and the

characteristics. (The rated of this fuse is 250V/3.15A.)

Operator

It is suggested that the operator of this product should have

proper Engineering background in Electronics and understand

the descriptions in this manual before start using. If an operator
doesn’t have such background, the operator has to operate this

product under the supervision of the person who has such

background in Electronics.

Connections

When you connect or disconnect this product with the other

GPIB instrument GPIB, please make sure that the power of

all the relevant instrument are turned off in advance.

Summary of Contents for ELS-304

















































































Search results

Summary of Contents for ELS-304

Reviews:

Brands by name

Popular brands

KG ELS-304, Operation Manual

Search results

Summary of Contents for ELS-304

Reviews:

Brands by name

Popular brands