manualshive.com logo in svg

KG ELS-304, Operation Manual

Share
Download
KG ELS-304 Operation Manual Download Page 31

ELS-304

 
 

Operations of Load Modes

 

5-1 

 

5. Operations for Load Modes 

 

 

There are seven (7) Load modes in this Product. There are the Constant Curr. (CC) , Constant 

Resistor (CR), Constant Volt. (CV), Constant Power (CP), External Control (EXT), Dynamic 
Load (DYNAMIC) ,and Short (SHORT) modes. Please check which Load mode you use and 

follow the operations relevant to the mode according to this manual.   

 
 

 

 
 

 

 
 

 
 

・ 

When you select a load mode, please switch OFF of the ON/OFF Switch. 

・ 

Otherwise, because, in some cases, the short condition will be setup, which may 
damage the target device. 

 

 
 

 

 
 

・ 

When you have no choice but to change the Load Range in the Load ON 
condition, the load will be in no-load condition for about 15msec when the range 

is switched.   

 

 

 

   

    Note:   If the I/O menu is displayed, you may be setting I/O parameters. 

              

Please finish setting in I/O menu, then exit from the I/O menu before 

        

you select/change a load mode.   

 
 

 

5.1

 

Load Mode

 

 

 

To select a load mode, press the “rotary knob” once to display “MODE” as shown below. 
While the “MODE” is displayed, you can select a load mode. 

 
 

 

 
 

 

 
 

 

Then you turn the knob, load modes that can be selected are displayed sequentially and 
repeatedly.  

 

 
 

 
 

CAUTION

NOTE

Once

Summary of Contents for ELS-304

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands