manualshive.com logo in svg

KG ELS-304, Operation Manual

Share
Download
KG ELS-304 Operation Manual Download Page 27

ELS-304

 
 

Operations

 

4-1 

 

4. Operations 

 

Names and functions of the operation panel, menu selection, memory function, and 

configuration setting are described. 

 

 

 

4.1

 

Operation Panel

 

 

 
 

 
 

 

 
 

 

 
 

 

 
 

 
 

 

 
 

(1)  Function keys 

These function keys are used to recall function allocated for each menu selected. 
 

  

(2) Ten keys 

These keys are for setting values like load current. 

 

 
(3)  Rotary knob  

With this convenient knob, you can increase/decrease a setting value or change item to 
be selected. And this knob can be used as a button to confirm the selected value.   

 

 
(4)  ON/OFF switch  

This switch is for setting Load ON/OFF.    When Load ON, the LED above this switch is 

turned ON.   

 

 

(5)  ENT key  

This key is for confirming inputted value(s) and selected conditions. 

 

 

(6)  CE key  

This key can be used to cancel data input and a commend you selected.   

 

 

(7) Menu key 

This key is used to select menu.   

 

 
 

 

7

4

1

0

.

2

5

8

9

6

3

CE

ENT

ON/OFF

F1

F2

F3

MENU

(1)

(2)

(3)

(6)

(5)

(4)

(7)

Summary of Contents for ELS-304

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands