manualshive.com logo in svg

KG ELS-304, Operation Manual

Share
Download
KG ELS-304 Operation Manual Download Page 24

ELS-304

 

 

3-2

 

  Name and Function of Each Part

 

 

 

(6) Trigger Output 

 

In dynamic (load) mode, sync. Signals in accordance with the edges of the load current 
will be outputted. This signal is isolated.   

 

(7) Power switch   

Switch for powering ON/OFF of this product. 

 

 
 

 

 

3.1.1

 

1

 

Details of the Display   

 
 

 
 

 

 
 

 

 
 

 

 
 

 

 
 

(1) Volt. Ranges  

The status of the selected voltage range is displayed: either 4V(Low) range or 30V(High) 

range. 

 

(2) Curr. Ranges  

The status of the selected current range is displayed: either 12A(Low) range or 

120A(High) range. 
 

(3) Meas. values  

Two meas. values are simultaneously displayed.  You can select what should be 
displayed. In the drawing, voltage and current are displayed in upper and lower columns 

respectively. 
 

(4) Function buttons  

Characters or icons currently allocated to F1-F3 are displayed.  
Items displayed therein depend upon the function you selected.  

 

 
(5) Load setting 

Selected load setting value is displayed. In dynamic mode, ”DYNAMIC” is displayed 
instead. 

 

 

(6)  Response speed (slew rate) setting value 

Setting response speed (slew rate) is displayed. In a mode that you cannot set response 

speed ”----“ is displayed instead. 
 

 

 
 

 

(3)

(1)

(2)

(4)

(8)

(7)

(6)

(5)

Summary of Contents for ELS-304

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands