Keysight Technologies S9100A Startup Manual Download Page 80

Page: 80 / 107

7 Run Power Calibration

7. 3. 4 Calibrating S9100A Option RH1

7. 3. 4. 1 Calibration 1 of 2: Power from RRH 1 RFHD 1 -> RRH 1 RFHD 2

This calibration is used to calibrate FR2 ports
(with

RF Tx/Rx 1

➀

used as the RF Output) on an

S9100A Option RH1 5G Multi-Band Vector Transceiver.

When performing this Power Calibration, the Source (Tx) output
power level is set to -5 dBm by default.

1. Calibrate the Source (Tx) signal path

a. Select the Power Calibration tab.

b. Select the Operation drop-down arrow and select

Calibration

c. Select the Calibration Step(s) drop-down arrow and select

Complete

d. Select the Port Selection drop-down arrow and

select

RRH 1 RFHD 1 -> RRH 1 RFHD 2

e. Select

Start the calibration

and follow the prompts.

f. Connect the U8487A Power Sensor or equivalent to

M1740A mmWave Transceiver connector

RF Tx/Rx 1

➀

g. Select

to continue the calibration.

View the

Results Source

tab when the calibration is complete.

Corrections are stored in:

S9100ID_<SerialNumber>-

Tx-RFIO_1-CHANNELPOWER.csv

S9100A 5G Multi-Band Vector Transceiver, Startup Guide

Summary of Contents for S9100A












































































































Search results

Summary of Contents for S9100A

Reviews:

Brands by name

Popular brands

Keysight Technologies S9100A, Startup Manual

Search results

Summary of Contents for S9100A

Reviews:

Brands by name

Popular brands