Keysight Technologies AC6801B Operating And Service Manual Download Page 195

Page: 195 / 197

Cleaning and Replacing the Filter

The following procedure illustrates the AC6804B instrument, but the same procedure applies to all
the AC6800B units.

Step 1. With your thumbs, press on the two dimples located on the front panel grill.

Step 2. While pressing on the dimples, use your forefingers to press on the grips and slide the grill
down.

Step 3. Detach the front grill.

Step 4. Remove the filter and clean it by rinsing it in water. Ensure that the filter is completely dry
before reinstalling it.

Step 5. Align the plastic fingers on the back of the grille with the slots on the sheet metal.

Step 6. With your thumbs, press the two dimples located on the front panel grill.

Step 7. While pressing on the dimples, use your forefingers to press on the grips and slide the grill up.

Keysight AC6800B Series Operating and Service Guide

195

4 Calibration, Verification, and Service

Summary of Contents for AC6801B






































































































































































































Search results

Summary of Contents for AC6801B

Reviews:

Related manuals for AC6801B

Brands by name

Popular brands

Keysight Technologies AC6801B, Operating And Service Manual

Search results

Summary of Contents for AC6801B

Reviews:

Related manuals for AC6801B

Brands by name

Popular brands