Kaufman & Robinson eHC 15015A Manual Download Page 64

Page: 64 / 67

APPENDIX 8-1

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

8. APPENDIX

The auto controller is preset to match the product supplied with it so the user should

usually not need to enter the setup mode. The setup is provided in case there has

been a change to the original product.

8.1 Auto Controller Setup

1. Start with the controller off. Press and hold the Program select and the Ac-

quire Setpoints buttons while tuning on the power switch. Continue holding

the two buttons until the LED indicators on the front panel begin to

ash.

Set the maximum

ow for the mass

ow controller that will be attached to

the four gas channels. Use the Gas Channel Select button to select each

channel that will be used, then use the Gas Adjust knob to dial in the cor-

rect maximum

ow. When

nished, press and release the Operating Mode

button.

2. At this Point, the display alternately

ashes Lrn and on. This is the learn

mode for the auto controller. When the auto controller is being used to run

the discharge of an end-Hall ion source in auto mode, it will learn how to

reach the operating conditions the

rst time a program is used. The next

time, the feedback will home in more quickly. Since this effects the starting

gas

ow, it may be desirable to turn this off for some applications. Turn the

setpoint knob to select off if desired. When

nished, press and release the

Operating Mode button. Note that the learn mode does not function when

operating the auto controller remotely using the remote setpoint option.

3. The display now reads bd3. This is the baud rate selection for RS232 com-

munication with the auto controller. Turn the Gas Adjust knob to select

the baud rates. 0=1200, 1=2400, 2=4800, 3=9600, 4=19200, 5=38400,

6=57600, 7=115200. After selecting the desired baud rate, press and re-

lease the Operating Mode button.

4. The display should now read L16. This is the led brightness for the indica-

tor LED’s (not the display) turn the Gas Adjust knob to obtain the desired

brightness from L2 to L64. When

nished, press and release the Operating

Mode button.

5. The display should alternately

ash HC4 and 10. The number 10 is the mini-

mum

ow in sccm that the hollow cathode can be adjusted to when using

either the Auto Gas or Manual Gas Operating Mode. Use the gas adjust

knob to adjust the minimum

ow to a value other than 10 if desired. When

nished, press and release the Operating Mode button.

Summary of Contents for eHC 15015A




































































Search results

Summary of Contents for eHC 15015A

Reviews:

Brands by name

Popular brands

Kaufman & Robinson eHC 15015A, Manual

Search results

Summary of Contents for eHC 15015A

Reviews:

Brands by name

Popular brands