manualshive.com logo in svg

Kaufman & Robinson eHC 15015A, Manual

Share
Download
Kaufman & Robinson eHC 15015A Manual Download Page 57

DIAGNOSTICS                                                                                                    7-1

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

7. Diagnostics

The following information is intended to facilitate troubleshooting of the Auto Con-

troller and associated power supplies. This information assumes that the Auto 

Controller and power supplies are connected to power and that all interconnects 

between power supplies and the ion source cable are made correctly. It is also 

assumed that all gas connections are in good condition and that the gas circuit is 

complete from the gas bottle to the ion source.

Power must be removed from the Auto Controller and power supplies prior 

to performing maintenance.

7.1 Auto Controller

The auto controller front panel display has an additional function of displaying 

help codes and error messages. If it becomes necessary to display a help code 

or an error message, the Auto Controller may switch to standby mode depend-

ing on the particular code or message. The front panel display will alternate 

between displaying “HLP” and a number for the help code. The error messages 

will be displayed by alternating two abbreviated words. A description of the help 

codes and the error messages is given below in table 7-1 along with possible 

corrective action that may need to be taken.

Table 7-1. Help codes and error messages for the Auto Controller.

Help Code

or Error

Message

Description

Possible Causes and Corrective

Action

HLP 7

Communication for remote

RS-485 communication

was detected and then

lost.

Check the connections of the RS-

485 cables.

Make sure keeper, emission and 

discharge power supplies have 

input power and are turned on.

The HLP 7 message will

automatically be cleared when

communication is restored.

HLP 8

RS-232 Interface Serial

Common Error. 

 High

Informational display only. No ac-

tion taken on unit operation. Unit

Summary of Contents for eHC 15015A




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands