Kaufman & Robinson eHC 15015A Manual Download Page 22

Page: 22 / 67

INITIAL OPERATION 4-3

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

be cleared when the Auto controller is turned back on. A shut off signal

for the hollow cathode gas is also available for remote shut off without

turning off the Auto Controller.

During startup of the hollow cathode, the automatic sequencing of the

Auto Controller will raise the gas

ow to 100 sccm to ignite the hollow

cathode in the Auto gas or Manual gas operating modes. After ignition in

these two modes, the gas controller will then drop the

ow to the operating

ow. The recommended operating

ow is 10 sccm for up to 10 amps of

cathode emission current. One sccm should be added to this

ow for

each additional ampere of emission current above 10 amps. Operation

is possible using less than the recommended minimum, but will reduce

the lifetime of the hollow cathode insert. Contact KRI for advice on using

less

ow for the hollow cathode if necessary.

The gas

ow may be adjusted by selecting the gas channel and turning the

knob on the front panel of the gas controller before the auto controller is

enabled. For the initial operation, leave the gases set at the programmed

setpoint(s).

4.3.1.3 Keeper Current Setpoint

The setpoint for the keeper current in amps is shown in the display labeled

Keeper Amps on the Keeper Power Supply. Notice that the yellow setpoint

LED below the display is on to indicate that the setpoint is being viewed.

Once the Auto Controller is enabled, the run value will be displayed and

the green run LED will be on.

The keeper current setpoint can be adjusted by turning the Setpoint Adjust

knob on the front of the Keeper Power Supply. Note: If the emission

current is set to less than 0.5 amps, then it may be desirable to increase

the keeper current to 2.0 amps to promote longer cathode lifetimes. For

the initial operation, leave the keeper current at the 1.5 amp setpoint.

4.3.1.4 Emission Setpoints

The setpoints for the emission voltage in volts and the emission current

in amps are displayed on the front panel of the Emission Power Supply

in the displays labeled Volts and Amps. Notice that the yellow setpoint

LED below the display is on to indicate that the setpoint is being viewed.

Once the Auto Controller is enabled, the run values will be displayed and

the green run LED will be on.

Summary of Contents for eHC 15015A




































































Search results

Summary of Contents for eHC 15015A

Reviews:

Brands by name

Popular brands

Kaufman & Robinson eHC 15015A, Manual

Search results

Summary of Contents for eHC 15015A

Reviews:

Brands by name

Popular brands