Kaufman & Robinson eHC 15015A Manual Download Page 3

Page: 3 / 67

II CONTENTS

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

6.2.1 Remote enable of the four stored programs using the DB-37

Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

6.2.2 Remote Gas Channel Setpoint Description for the

DB-37 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

6.2.3 Remote Analog Setpoint Option on the DB-37 Connector . . . . . .6-3

6.2.4 Analog Outputs for the DB-37 Connector . . . . . . . . . . . . . . . . . . .6-4

6.2.5 Run Fault and Beam Good on the DB-37 Connector . . . . . . . . . 6-6

6.2.6 Description of the DB-37 pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

6.3 Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

6.4 Remote Control using the RS-232 Serial Interface . . . . . . . . . . . . . .6-10

6.4.1 Interface cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

6.4.2 Communication settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

6.4.3 Communication overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

6.4.4 Commands, queries and responses . . . . . . . . . . . . . . . . . . . . . .6-10

6.4.4.1 VRB - Verbose Command . . . . . . . . . . . . . . . . . . . . . . . .6-11

6.4.4.2 COM - Enable RS-232 Command or Status Query . . . . 6-12

6.4.4.3 *IDN? - Unit Identi

cation Query . . . . . . . . . . . . . . . . . . .6-13

6.4.4.4 *RST – Reset Command . . . . . . . . . . . . . . . . . . . . . . . . .6-14

6.4.4.5 *TST? – Self Test Query . . . . . . . . . . . . . . . . . . . . . . . . . .6-14

6.4.4.6 OUT - System Level Output Control Command

or Status Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15

6.4.4.7 MDE - Mode Set Command or Mode Query . . . . . . . . . . 6-15

6.4.4.8 BEAM - Beam Good Query . . . . . . . . . . . . . . . . . . . . . . .6-16

6.4.4.9 P - Program Value Read/Write Command . . . . . . . . . . . . 6-17

6.4.4.10 R - Monitor Command for Reading the Actual

Feedback Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21

6.4.4.11 CFG? – Query current system con

guration . . . . . . . . .6-22

6.4.4.12 LRN – Learn Command or Learn Query . . . . . . . . . . . . 6-22

7. DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

7.1 Auto Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

7.2 Keeper Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-4

7.3 Emission and Discharge Power Supplies . . . . . . . . . . . . . . . . . . . . . .7-6

8. APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

8.1 Auto Controller Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1

8. LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1

9 SERVICE AND TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . 10-1

FIGURES

2-1 Front view of controller for End Hall ion source. . . . . . . . . . . . . . . . . . . . . . 2-5

Summary of Contents for eHC 15015A




































































Search results

Summary of Contents for eHC 15015A

Reviews:

Brands by name

Popular brands

Kaufman & Robinson eHC 15015A, Manual

Search results

Summary of Contents for eHC 15015A

Reviews:

Brands by name

Popular brands