manualshive.com logo in svg

Kaufman & Robinson eHC 15015A, Manual

Share
Download
Kaufman & Robinson eHC 15015A Manual Download Page 38

REMOTE/AUTOMATED CONTROL                                                                    6-5

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

Table 6-3. Pin descriptions for analog outputs on the DB-37 connector.

Pin 

Number

Description

1

Emission Current Output. 0-5 volts corresponds with 0 to the maximum 
Bias current in amps for the Emission Power Supply being used. Refer-
enced to pin 7 or 8.

6

Emission Voltage Output. 0-5 volts corresponds with 0 to the maximum 
output voltage for the Emission Power Supply. Referenced to pin 7 or 8.

7

Common.

8

Common.

9

Channel 1 Gas Flow Output. 0-5 volts corresponds with 0 to the maxi-
mum output in sccm for the channel 1 MFC. Referenced to pin 27.

10

Channel 3 Gas Flow Output. 0-5 volt corresponds with 0 to the maxi-
mum output in sccm for the channel 3 MFC. Referenced to pin 27.

20

Discharge Current Output. 0-5 volts corresponds with 0 to the maximum 
level of discharge current in amps for the Discharge Power Supply that 
is being used.

21

Discharge Voltage Output. 0-5 volts corresponds with 0 to the maximum 
level of discharge voltage in volts for the Discharge Power Supply that is 
being used.

25

Keeper voltage output. 0-5 volts corresponds with 0-800 volts. Refer-
enced to common pin 7 or 8.

27

Gas 

fl

 ow Output common.

28

Channel 2 Gas Flow Output. 0-5 volts corresponds with 0 to the maxi-
mum output in sccm for the channel 2 MFC. Referenced to pin 27.

29

Channel 4 Gas Flow Output. 0-5 volts corresponds with 0 to the
maximum output in sccm for the channel 4 MFC. Referenced to pin 27.

37

Keeper current output. 0-5 volts corresponds with 0-2 amps. Referenced
to common pin 7 or 8.

Summary of Contents for eHC 15015A




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands