manualshive.com logo in svg

Kaufman & Robinson eHC 15015A, Manual

Share
Download
Kaufman & Robinson eHC 15015A Manual Download Page 40

REMOTE/AUTOMATED CONTROL                                                                    6-7

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

brief; see the detailed descriptions above to understand the full functionality.

Table 6-5. Pin descriptions for the female DB-37 connector on the Auto Con-

troller.

Pin 

Number

Description

1

Emission Current Output. 0-5 volts corresponds with 0 to the maximum 
emission current in amps for the Emission Power Supply being used. 
Referenced to pin 7 or 8.

2 No 

Contact

3

Discharge Voltage Setpoint. 0-5 volts corresponds with 0 to the maxi-
mum output voltage for the Discharge Power Supply. Referenced to pin 
7 or 8.

4

Emission current set point. 0-5 volts corresponds with 0 to the maxi-
mum emission current in amps for the Emission Power Supply being 
used. Referenced to pin 7 or 8.

5 

Aux 12 volts. Referenced to pin 7 or 8.

6

Emission Voltage Output. 0-5 volts corresponds with 0 to the maximum 
output voltage for the Emission Power Supply. Referenced to pin 7 or 8.

7 Common.
8 Common.
9

Channel 1 Gas Flow Output. 0-5 volts corresponds with 0 to the maxi-
mum output in sccm for the channel 1 MFC. Referenced to pin 27.

10

Channel 3 Gas Flow Output. 0-5 volt corresponds with 0 to the maxi-
mum output in sccm for the channel 3 MFC. Referenced to pin 27.

11

Channel 1 Gas Setpoint. 0-5 volts corresponds with 0 to the maximum 
output for the MFC connected to Channel 1. Referenced to pin 13.

12

Channel 3 Gas Setpoint. 0-5 volts corresponds with 0 to the maximum 
output for the MFC connected to Channel 3. Referenced to pin 13.

13

Gas Setpoint Common.

14

Gas Channel 3 shut off. Connecting this pin to common pin 7 or 8 will 
disable the gas 

fl

 ow to the MFC and deactivate the additional MFC relay 

for channel 3, regardless of the input 

fl

 ow setting.

Summary of Contents for eHC 15015A




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands