manualshive.com logo in svg

Kaufman & Robinson eHC 15015A, Manual

Share
Download
Kaufman & Robinson eHC 15015A Manual Download Page 14

INSTALLATION                                                                                                    3-3

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

3.4 Connections Between Controller Components

The connections between Controller components are shown in Fig. 3-2, which 

shows the rear panels of the Auto Controller, and the Keeper, Emission and 

Discharge power supplies. The individual connections required are given be-

low:

• If the 6 meter (20 ft.) input power supply cables were not connected to the 

individual power supplies when they were installed in the cabinet, connect 

them now. Use plugs that will match the input power sources. Again, do not 

connect to Input Power before the installation is complete.

• Attach the 4 pin (female) plug connector of the 6 meter (20 feet) operating  

cable to the connector on the electrical feedthrough. The connections for 

the other end of this cable are described below.

• Insert the end of the operating cable BLUE wire into one of the (+) positive 

connectors located on the rear panel of the Discharge Power Supply and 

tighten the screw above the appropriate connector.

• Insert the end of the operating cable BLACK wire into one of the (-) negative 

connectors located on the rear panel of the Discharge Power Supply and 

tighten the screw above the appropriate connector.

• Insert the end of the operating cable RED wire into one of the (-) negative 

connectors located on the rear panel of the Keeper Power Supply and tight-

en the screw above the appropriate connector.

• Insert the end of the operating cable ORANGE wire into one of the (+) Posi-

tive connectors located on the rear panel of the Keeper Power Supply and 

tighten the screw above the appropriate connector.

• Insert one end of the short RED wire into one of the (-) negative connectors 

located on the rear panel of the Keeper Power Supply and tighten the screw 

above the appropriate connector.

• Insert the other end of the short RED wire into one of the (-) negative connec-

tors located on the rear panel of the Emission Power Supply and tighten the 

screw above the appropriate connector.

• Insert one end of the short BLACK wire into one of the (+) positive connec-

tors located on the rear panel of the Emission Power Supply and tighten the 

screw above the appropriate connector.

Summary of Contents for eHC 15015A




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands