manualshive.com logo in svg

Kaufman & Robinson eHC 15015A, Manual

Share
Download
Kaufman & Robinson eHC 15015A Manual Download Page 23

4-4                                                                                           INITIAL OPERATION

_______________________________________________________________________

Copyright © 2010 by Kaufman & Robinson, Inc., 1306 Blue Spruce Drive, Unit A, Fort Collins, CO 80524
Tel: 970-495-0187, Fax: 970-484-9350, Internet: www.ionsources.com

The Emission voltage and current setpoints can be adjusted by turning 

the Setpoint Adjust knob on the front of the Emission Power Supply. The 

setpoint being adjusted by the knob is indicated by the green LED’s on 

the front panel labeled Amps and Volts. These LED’s are located above 

and below the white Select button on the front panel of the Emission 

Power Supply. Pressing and releasing the Select button will switch the 

parameter being adjusted from Amps (emission current) to Volts (emission 

voltage) or from Volts to Amps. This can only be adjusted independently, 

but is also adjusted automatically when adjusting the Discharge current. 

This maintains the same Emission to Discharge current ratio. For the 

initial operation, leave the Emission at the program setpoint.

4.3.1.5 Discharge Parameters

The setpoints for the discharge voltage in volts and the discharge current 

in amps are displayed on the front panel of the Discharge Power Supply 

in the displays labeled Discharge Volts and Discharge Amps. Notice 

that the yellow setpoint LED below the display is on to indicate that the 

setpoint is being viewed. Once the Auto Controller is enabled, the run 

values will be displayed and the green run LED will be on.

The discharge voltage and current setpoints can be adjusted using the 

Setpoint Adjust knob on the front of the discharge controller. These 

adjustments can be made when the Auto Controller is in Standby or when 

it is Enabled. The setpoint being adjusted by the knob is indicated by the 

green LED’s on the front panel labeled Amps and Volts. These LED’s are 

located above and below the white Select button on the front panel of the 

Discharge Power Supply. Pressing and releasing the Select button will 

switch the parameter being adjusted from Amps (discharge current) to 

Volts (discharge voltage) or from Volts to Amps. For the initial operation, 

leave the discharge voltage and current at the program setpoints.

4.3.1.6 Enable

Press and release the white Enable/Standby button on the front panel 

of the Auto Controller. Notice that the yellow Standby LED under the 

button turns off and the green Enable LED above the button turns on. 

The same LED transition from Standby to enable also happens on the 

Keeper, Emission and Discharge Power Supplies as the Auto Controller 

sequences them on. The gas 

fl

 ow will automatically be adjusted until the 

program 1 parameters are reached.

Note that the operating range of the ion source may be limited by the 

Summary of Contents for eHC 15015A




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands