26
English
5.906-736.0 Rev. 00 (07/15)
DANGER
Risk of explosion!
Do not spray flammable liquids.
DANGER
Risk of injury! Never use the appliance without the spray
lance attached. Check and ensure proper fitting of the
spray lance prior to each use. The screw connection of the
spray lance must be fingertight.
몇
WARNING
Long hours of using the appliance can cause circulation
problems in the hands on account of vibrations.
It is not possible to specify a generally valid operation time,
since this depends on several factors:
–
Proneness to blood circulation deficiencies (cold, numb
fingers).
–
Low ambient temperature. Wear warm gloves to pro-
tect hands.
–
A firm grip impedes blood circulation.
–
Continuous operation is worse than an operation inter-
rupted by pauses.
In case of regular, long-term operation of the device and in
case of repeated occurrence of the symptoms (e.g. cold,
numb fingers) please consult a physician.
1 Stop cock water tanks
The water supply can either take place via an external wa-
ter supply or via the internal water tanks (2x250 litres).
–
External water supply:
Close stop cock water tanks.
–
Internal water supply:
Open stop cock water tanks.
NOTE
The device can only be operated when the front cover is
closed. If the front cover is opened, the device shuts down
and the indicator light is on.
NOTE
Due to the bleeding procedure, the speed of the motor
may vary until the final operating pressure has been
reached.
Unlock the emergency-stop switch by pulling.
Open rear cover.
Establish the water supply.
Insert the key into the key switch.
To preheat the motor, turn the key switch to the left and
hold it until the indicator light preheating goes out.
NOTE
The indicator light preheating lights up for approx. 4 sec-
onds if the key switch is turned to the left. Then the indica-
tion goes out.
The preheating itself takes place as long as the key switch
is in the "preheating" position.
Turn key switch to position "I". The indicator lamp for
operational readiness lights up.
The control voltage is switch on and the display shows
the operating status.
Turn the key switch to the right until the motor is run-
ning.
NOTE
The indictor light standby mode is on for approx. 6 seconds
after the start of the motor. Then the indication goes out.
Operating with cold water:
Set the power switch to "0/OFF“ (burner off).
Operation with warm water:
DANGER
Scalding danger!
Set the power switch to the desired working tempera-
ture (max. 100 °C). The burner is switched on.
Press the lever on the hand spray gun.
8
Operations
8.1
General information on the operation
8.1.1
Safety instructions
8.1.2
Water supply
8.1.3
Turning on the Appliance
Summary of Contents for HDS 9/50 De Tr1
