– 7
Customer Service Engineer or an elec-
trician.
Check the high pressure hose for dam-
ages (risk of bursting).
Please arrange for the immediate ex-
change of a damaged high-pressure
hose.
Check oil level from the oil level display
of the high pressure pump.
Please contact Customer Service im-
mediately if the oil is milky (water in oil).
Check appliance (pump) for leaks.
3 drops per minute are permitted and
can come out from the lower side of the
appliance. Call Customer Service if
there is heavy leakage.
Clean filter at the water connection.
Change oil in the pump.
Have annual customer service work
performed.
Change the oil in the high pressure pump.
For oil type refer to technical specifica-
tions.
Turn out the oil drain screw.
Drain the oil in a collection basin.
Screw in oil drain plug.
Fill in new oil slowly until the centre of
the oil level display.
Note:
Air pockets must be able to leak out.
You can rectify minor faults yourself with
the help of the following overview.
If in doubt, please consult the authorized
customer service.
DANGER
Risk of injury by inadvertent startup of ap-
pliance and electrical shock.
–
Prior to all work on the appliance,
switch off the appliance and pull the
power plug.
–
Get the electrical components checked
and repaired only by authorised cus-
tomer service persons.
–
Contact an authorised customer service
person in case of problems not men-
tioned in this chapter or if you are in
doubt or when you have been explicitly
asked to do so.
The indicator lamps display the operating
states (green).
Reset:
Set the appliance switch to "0".
Wait for a while.
Set the appliance switch to "1".
Continuous green:
– The appliance is now ready for opera-
tion.
If indicator lamp no display, means not
connected.
– No power
Check whether the voltage indicated on
the type plate corresponds to the volt-
age of the socket.
Check the mains connection cable for
damages.
– Motor overloaded/ over-heated.
Switch off appliance and let it cool
down. Remove the cause of the prob-
lem. Turn on the appliance again.
– Wrong nozzle
Check nozzle for correct size (see tech-
nical specifications).
– Flushed the nozzle.
Clean/ replace nozzle.
– Filter is dirty.
Clean filter at the water connection.
Unscrew the filter casing, remove the
filter, clean it and replace it.
– Air within the system
Appliance ventilation:
Unscrew the nozzle. Switch on the ap-
pliance and let it run until the water ex-
iting from the spray pipe is bubble-free.
Weekly
After 50 operating hours
Yearly or after 500 operating hours
Troubleshooting
Indicator lamp
Operating status display
Fault indication
Appliance is not running
Device is not building up pressure
9
EN
Summary of Contents for Cage Classic HD 13/35-4
