– 3
The switch prevents unintented starting of
the appliance. Stop the appliance during
breaks or after operation.
The safety catch on the trigger gun pre-
vents the appliance from being switched on
unintentionally.
While reducing the water supply/quantity
regulation at the pump head, the overflow
valve opens and part of the water flows
back to the pump suck side.
When the lever of the hand spray gun is re-
leased, the overflow valve switches to cir-
cuit operation. The water flows back to the
suction side of the pump.
The thermal valve protects the high-pres-
sure pump from unacceptable heating dur-
ing circuit operation.
The thermo-valve opens when the permis-
sible water temperature is exceeded and
lets out the hot water into the open.
Thus, cold water will follow and cool the
pump.
The overload relay switches off the motor,
when there is no voltage in one of the phas-
es or there is a thermal overload.
If the overflow valve is defective, the safety
valve guides the entire flow rate of the
pump to the outside and thus protects the
device and accessories against inadmissi-
bly high overpressure.
DANGER
Risk of injury! Device, tubes, high pressure
hose and connections must be in faultless
condition. If they are not in a perfect state
then the appliance must not be used.
Check oil level of the high pressure
pump.
The oil level must be at the centre of the
oil level display.
Add oil if required (see technical speci-
fications).
Fasten the pushing handle with the four
screws, washers and nuts enclosed in the
packet.
몇
WARNING
Risk of injury on account of unsuitable ac-
cessories. Only use accessories approved
for the working pressure of the appliance
(see "Specifications").
Only install accessories when the appli-
ance is switched off.
The maximum torque for the screw connec-
tions of the high pressure hose is 20 Nm.
Connect high pressure hose and spray
pipe to the hand spray gun.
Mount the power nozzle on the spray
pipe. Tighten covering nut firmly.
Connect the high pressure hose to the
high pressure connection point of the
machine.
– For connection values refer to technical
specifications.
– The electrical connections must be
done by an electrician according to IEC
60364-1.
Power switch
Safety catch
Overflow valve
Thermostat valve
Overload relay
Safety valve
Start up
Check oil level
Installing the pushing handle
Attaching the Accessories
Power supply
5
EN
Summary of Contents for Cage Classic HD 13/35-4
