JVC DT-V1710CG Service Manual Download Page 65

Page: 65 / 76

(No. 52152) 1-65

LOW-LIGHT WHITE BALANCE (REFERENCE VALUE) ADJUSTMENT

Measuring Instruments

Signal generator (Crosshatch signal, 10-step gray scale signal)
Oscilloscope

Card (Slot)

Component/RGB Input Card (Slot 1)

Test Points

TP-47R, TP-47G, TP-47B [CRT SOCKET PWB]
TP-GND [CRT SOCKET PWB]

Adjustment Points

SCREEN VR [Bottom potentiometer on high-voltage transformer]
W*04 (Cut Off (R)), W*05 (Cut Off (G)), W*06 (Cut Off (B)) [Service Menu]

Notes:

•

Perform the following adjustments after completing
the screen size adjustment.

•

Set the COLOR TEMP./BAL. data in the Setup Menu to
“00”.

(1) Apply the 1080/60i component crosshatch signals to INPUT

(2) Set “COLOR TEMP.” of COLOR TEMP./BAL. in the Setup

Menu to HIGH.

(3) Set the PHASE, CHROMA, BRIGHT and CONTRAST

potentiometers on the front panel to the center click positions.

(4) Observe the AKB pulse waveforms of TP-47R, TP-47G, TP-

47B and ensure that the voltage <A> of the smallest AKB
Pulse color is

25V ± 2V

. If it is not, readjust it, using the

SCREEN VR

(5) Apply the 1080/60i component 10-step gray scale signal to

INPUT A.

(6) Turn the BRIGHT potentiometer on the front panel gradually

until the second gray step in the gray scale lights slightly.
(Do not touch the SCREEN VR potentiometer.)

(7) Adjust

WW04

WW05

and

WW06

in the Service Menu so

that the gray bars are not tinted. (Do not set the values of

WW04

WW06

no more than “

”.)

(8) Write the data of

WW04

WW06

WX04

WX06

without

any alteration. (Do not adjust the

items.)

4.10.11 WHITE BALANCE ADJUSTMENTS

1 Vertical interval

(V. sync)

AKB Pulse

V. BLK

<A>
25V ± 2V

Let this bar light up slightly

Summary of Contents for DT-V1710CG













































































Search results

Summary of Contents for DT-V1710CG

Reviews:

JVC DT-V1710CG, Service Manual, Page: 65 / 76

Search results

Summary of Contents for DT-V1710CG

Reviews: