manualshive.com logo in svg

JVC DT-V1710CG, Service Manual, Page: 13 / 76

Share
Download
JVC DT-V1710CG Service Manual Download Page 13

(No. 52152)  1-13

4.1 ADJUSTMENT PRECUTION

(1) Make sure that connection is correctly mode AC to AC power souce.

(2) Warm run the unit and measuring tools sufficiently (at least 30 minutes).

(3) Perform all adjustments based on the initial values. There is no problem if the result of an adjustment performed by observing

the screen is different from the initial value.

(4) Never attempt to turn on potentiometers or other controls that are not explicitly mentioned in the adjustment procedures.

NOTE:

When using the IF-C01PNG (NTSC/PAL Video Input Card) in an adjustment, be sure to check the output waveforms

from the video input card in advance.

4.2 SETTINGS REQUIRED FOR ADJUSTMENTS

For the functions other than those that should be set before each adjustment, reset them to the initial values

according to the table on page 1-10 before proceeding to the adjustment.

Correct adjustments will not be possible unless the values of the functions are reset to the initial values.

4.3 SETTING ITEMS

Begin adjustments with the primary items and then proceed to the secondary items, (1) to (3).

!

PRIMARY ADJUSTMENT ITEMS

•

Screen voltage coarse adjustment

•

High-voltage coarse adjustment

•

X-ray protector adjustment/check

•

High-voltage adjustment

•

Focus adjustment

•

Image rotation adjustment

•

Convergence adjustment

!

SECONDARY ADJUSTMENT ITEMS (1)

•

Contrast adjustments

•

Chroma/Phase adjustments

!

SECONDARY ADJUSTMENT ITEMS (2)

•

Deflection system adjustments

(Overscan, underscan, aspect mode)

!

SECONDARY ADJUSTMENT ITEMS (3)

•

White balance adjustments

•

Brightness adjustments

(Overscan, underscan, aspect mode)

SECTION 4

ADJUSTMENT

Summary of Contents for DT-V1710CG













































































Reviews:

No comments