manualshive.com logo in svg

JVC DT-V1710CG, Service Manual, Page: 54 / 76

Share
Download
JVC DT-V1710CG Service Manual Download Page 54

1-54  (No. 52152)

CHROMA ADJUSTMENTS (PAL)

Measuring Instruments

Signal generator (Color bar signal)
Oscilloscope

Card (Slot)

NTSC/PAL Video Input Card (Slot 2)

Test Points

TP-47B [CRT SOCKET PWB]
TP-GND [CRT SOCKET PWB]

Adjustment Points

S*03 (Chroma) [Service Menu]

Notes:

•

Ensure that the output waveforms from the NTSC/PAL
Video Input Cards are normal before proceeding to the

following adjustments.

•

Perform the following adjustments after completing
the 1080/60i signal Chroma/Phase Adjustments.

•

Set the CHROMA and PHASE data in the Setup Menu
to “00”.

•

The SR value (see the description of the Component
Signal Chroma/Phase Adjustments) becomes the

reference value for the following adjustments. When

this data is changed, it is required to re-adjust the data

of all of the adjustment signals (Component, NTSC and

PAL).

When re-adjusting the 1080/60i signal, use the SI. (For

the adjustment of the 1080/60i signal, use the

Component/RGB Input Card.)

(1) Apply the PAL 75% color bar signal to INPUT C (Terminal

VIDEO1 on the NTSC/PAL Video Input Card).

(2) Set the CHROMA and PHASE potentiometers on the front

panel to the center click positions.

(3) Connect the oscilloscope across TP-47B and TP-GND.
(4) Adjust 

SC03 

in the Service Menu to set the level difference

between waveforms 1 and 4 in the figure on the right to 

0

V ± 2 V

.

(5) Apply the PAL 75% color bar signal to INPUT D (Terminal

Y/C on the NTSC/PAL Video Input Card) and perform the
adjustments in steps 2 to 4 above. See Table 7 for the
adjustment data.

Table 7

Adjustment

Adjustment Data

Signal

Chroma

PAL (VIDEO)

SC03

PAL (Y/C)

SD03

4

3

2

1

Summary of Contents for DT-V1710CG













































































Reviews:

No comments